top of page

Your racquet comes off the machine shorter than it went on

5 days ago
5 min read

Updated: 11 hours ago

Two or three millimetres of length lost, one or two of width gained: on some frames, the measurement comes back every time. Stringers who track it often compensate by stringing the crosses slightly higher than the mains. It does bring the frame back to its shape. The question is whether you want it to: the distortion is normal, and compensating for it changes how the racquet plays.

The frame check tool, at the bottom of this article, runs the numbers on your own measurements.

A string bed is a closed spring

A racquet frame is a carbon ring. Stiff out of its plane, it is far more flexible within it, and there it takes the shape the strings impose.

The mains pull the head towards the throat: the hoop shortens and, like a ring squeezed at both ends, it widens. The crosses pull the two sides towards each other: the hoop narrows and lengthens.

While stringing, the machine's supports hold the shape. Once unmounted, the frame settles where the two families of forces balance. That balanced shape is what you measure after stringing, and it is what you play with. A racquet that comes off shorter is telling you one thing: the mains won.

Why the mains win at equal tension

On the machine, mains and crosses show the same number. In the frame, they are not the same force.

  • Friction. A main is pulled in a straight line, from one grommet to the other. A cross is pulled through every main it crosses, over, under. Each crossing holds back part of the pull: the string is at the set value near the tensioner, less so further away. Published laboratory measurements on racquets strung at a single value found crosses clearly less tight than the mains, with the gap lasting for months.

  • Weaving. Threading the crosses makes the mains wave around them: they lengthen slightly and their tension rises. The mains gain force at the very moment the crosses go in.

The machine's number describes the pull at the tensioner, not what stays in the string. At the same displayed value, the mains weigh more in the balance, and the frame shortens.

Why some frames move more than others

For the same forces, a frame distorts more when its section is thin in the plane of the string bed. Narrow, aero-profiled beams carry little material where that stiffness is decided: they give more than thick-section frames.

Mounting matters too. On a 6-point mount, the side supports hold the frame throughout. On a 2-point mount nothing holds the sides: stringing order is the only protection for the width.

Hence what a careful stringer keeps finding: the same millimetres, on the same model, job after job. It is not a technique error. It is a property of the frame.

Measure before you compensate

You only correct what you have measured.

  1. Bare frame, old strings out: inside length of the hoop, head to throat bridge, and inside width at the widest point. Always at the same points, with the same rule, to the half-millimetre.

  2. If you can, the width after the mains, racquet still on the machine: that is where the widening shows best.

  3. The same measurements after the last knot, racquet unmounted.

How to read them:

  • Up to 1 mm: that is measuring precision, nothing to correct.

  • 1 to 3 mm of length, with roughly as much width gained: that is the mains-crosses balance: normal, and adjustable with tension if you want.

  • Beyond 3 mm, or width moving on its own: check mounting and stringing order before touching tension.

  • Beyond 5 mm: have the frame checked before playing it.

Compensating in the crosses: what it fixes, what it costs

Stringing the crosses higher gives the sides back the force friction took from them. The frame returns towards its shape, and the mains keep the tension they were losing as the frame closed in on them. It is a balance correction. Nothing makes it compulsory: a frame that has shortened by two or three millimetres is not damaged, it simply plays with the balance its strings give it.

Above all, it is a playing choice. Tighter crosses grip the mains and let them slide less: the bed becomes firmer and more consistent in the centre, and the mains snap back less readily after impact. You gain control on driven trajectories and flat hitting. You lose access to topspin and the ease of hitting high, looping balls. A player who lives on topspin often does better keeping the distortion; one who hits flat can look for the correction. Beyond a two-kilo gap, the string bed changes more than the frame gains.

If that is the effect you want, the method takes two stringing jobs. In this range the frame behaves like a spring: its distortion follows the force. String once with one extra kilo on the crosses, measure, and the two jobs are enough to draw the line that gives the tension gap bringing length change back to zero. If that gap exceeds two kilos, tension is no longer the right lever.

Before touching tension: what you can fix without it

  • Supports at contact, no force. Overtightened, they shape the frame instead of holding it, and the end-of-job measurement lies.

  • Alternate the mains. Never more than three or four mains ahead on one side.

  • Crosses with less friction. Weave one cross ahead, pull in a wide arc, square to the string bed. Less friction means a cross that ends closer to its value, and less gap to compensate.

  • Clamp tight to the frame. A few millimetres too far and the string relaxes between clamp and grommet: tension lost, almost always on the crosses.

Each of these is detailed in the four-knot method and stringing mistakes.

Run the numbers on your frame

Enter the measurements before and after stringing, and both tensions. The tool tells you whether mains or crosses won and, if you want to cancel the distortion, the cross tension that gets you there. Name the frame to keep its log: from two jobs at two different gaps, it draws the line and gives the tension gap that cancels the distortion. The log stays in your browser.

Frequently asked questions

Should crosses always be strung higher than mains?

No. The distortion is normal, and compensating for it is a playing choice: more control on flat shots, less access to topspin. On a frame thick in its plane, a well-run job at a single value does not move by a millimetre anyway.

By how much?

If you want it: by what the measurement says, in one-kilo steps, staying under a two-kilo gap.

What about a hybrid?

A multifilament cross rubs less on the mains and stretches more under the pull: the balance changes, so measure again. See hybrid strings.

Is my racquet damaged?

Distortion that disappears when the strings come out is elastic: the frame is fine. Distortion that stays on the bare frame is not: have it checked before restringing.

Prefer to hand it over? Workshop stringing is done the same day. To learn to do it yourself, the stringing course runs on a professional machine, with follow-up for as long as you need.


Comments


bottom of page